Trench Digger 3 Step In
With over 15 years of manufacturing snowboard plate bindings and with our success of both the TD1 and TD2, Bomber Industries is proud to announce the Trench Digger 3.
see also Standard Model
We also offer gift certificates!
IN STOCK NOW!
SALE! Buy a TD3 and get a free set of e-rings (your choice)! (to be added at time of processing)
|
With close to three years of development, the TD3 is a combination of the solid foundations of the famous TD1 and TD2 but with all the improvements and changes the carving community has demanded. Over the years the Bomber Trench Digger line has had a reputation of being a “set and forget” binding. We have no plans to change that with unnecessary adjustments and parts. Keep it simple, keep it strong. Being a small and passionate group (and on some days, quite outspoken) it is easy to see what the modern day carver demands in their bindings: reliability and performance. We have listened and we are delivering.Fin-Tec heels sold separately.SOLD IN PAIRS |
For help in selecting disks, go here.
New in the TD3:
Extra Thick E-Ring: 7mm total thickness versus 2.5mm of TD2. An amazing amount of absorption and movement of the binding may now be achieved.
Hard Stops on Bails: No more floppy bails or springs to worry about. All bails have hard stops to keep the bails in their “cocked” position. This includes the Toe Bail for the standard binding - keeping it in a “ready” position to make manual entry a breeze.
Hardened Steel Step-In Receiver: No more galled up aluminum step-in receivers that seem to attract snow and ice. The new steel receiver makes for super smooth step-in action and incredible wear resistance. We also added an “Ice Buster” lock-bracket to hold the receiver down that incorporates a sharp ridge to facilitate snow and ice removal from the bottom of the heel.
Through Shaft Design on Bails: No more shoulder bolts, the TD3 uses a one piece through shaft to connect the lugs/bail assembly to the binding. Simple, strong, and on line with the Trench Digger's reputation for set-and-forget reliability. We also still maintained the Micro-Adjustable of the lugs if needed for fine tuning the boot fit.
New Base Plate Design: the new Base Plate for the TD3 has the center section removed allowing you to access the Center Disk for ease of removal and installation of the entire binding. Need to remove the binding for waxing or travel? No problem, back off the 4 screws and good to go. No more need to disassemble the entire binding.
Super Low Profile Toe Clip: The new TD3 toe clip has the lowest profile on the front of the boot of any toe clip out there. We designed the new toe clip around all current day modern snowboard hardboots to minimize overhang that has become an issue with today’s lower angles used in carving. We also increased the lever arm to reduce the effort of clipping in.
Nickel Coated Parts: We have selected a few key parts to receive a Nickel coating for its amazing protective properties, but more importantly it is very effective at resisting and repelling ice and snow.
Compatibility with TD2: The TD3 uses the same Cant/Lift disks as the TD2. So no need to start over with your selection of cant/lift disks, they will work on the TD3. Erings, however, are not compatible.
Same Great Features of the Trench Digger Line of Bindings:
Fully Suspended Binding: the TD2 introduced the concept of suspending the entire binding with a two piece lower assembly that uses a pad called the E-Ring for vibration absorption and allows for movement in the binding. The old TD2 system was based from a 2.5mm thick E-Ring. The new TD3 system is a supercharged version of this concept. We have increased the height of the E-Ring to 7mm and are now using a proprietary material designed just for our application. As before the new TD3 E-rings are available in soft (yellow), medium (blue), and hard (red) so you may tune the suspension of the binding.
Adjustable Cant and Lift: The TD3 is available at the time of purchase with any combination of 0, 3, or 6 degree cant/lift disks. These disks are then rotatable under the binding (in 5 degree increments) to allow you to adjust the angle of cant/lift.
Aluminum and Stainless Steel Construction: As always Bomber does not make wimpy gear! The TD3 uses strong and dependable materials where it is most important. A reliable binding that you do not have to think about while making a high-G turn is our goal.
Laser Engraved Settings: Lets be honest, we love numbers and the ability to quantify our set-ups. The TD3 has easy to read laser engraved angle indicators that are also used to determine your cant/lift angles. This allows you to keep track of your set-ups and be repeatable in your adjustments.
Other Features of the TD3: 5mm hex sockets (key included), 3 and 4 hole compatible disks available, 360 degrees of stance angles, our famous 5 Year Warrantee, and of course great customer service.
5 Year Warrantee & Full Parts Support: We trust our products so much, we back up the TD3 with the best warrantee in its class: 5 years from date of purchase. We also have full parts support in the Bomber Store if you need something fast.
All TD3 bindings come complete with: bindings, mounting hardware, leash, 5mm Hex Key, and detailed instructions.
TD3 bindings function properly ONLY with DIN standard boots.
For TD3 Dealers, go here.
