Ronin42
December 28th, 2009, 11:19 PM
...SOLD...
Dear BOL folk. I have noticed that some of the postings for sale are hard to respond to, so to make it easier I will leave my email at the bottom plus I believe my PM works.
OK here is the deal. I have a 173 BJ Slater /BS race boards/ Liberation Sports that is just too stiff for me.
The Good news: This board appears to never have been ridden there are no binding marks and the Camber is 11 mm+ on the floor and a whopping 32mm+ if against a wall. The edges are perfect, the deck is perfect using Rays way I checked the flatness of the base not concave not convex. and put a wax on it so it is ready to go.
The less then Great News: I would call this unused as opposed to new. It looks like there are a few factory blemishes.
#1 The Top sheet has what I will call a wrinkly in the red circle around the L about 1 inch long.
#2 The base right at the very back near the tail has three concave recesses where the base was pulled up into the board as it cooled. see their photo but I know it is almost impossible to see. So I don't recommend this board to anyone earning a living by going fast. for the rest of us we will never notice it.
#3 in the base I flat about a small (quarter sized bump) that was in the red circle around the L in the nose, again one can see where it was in person but not in these photos.
#4 the sidewall on the left side looks like it did not come out of the mold cleanly no core showing but not new either.
So there it is a way fast very stiff 173 GS board that has never been ridden and is completely ready to be pushed hard.
Something is worth what you can sell it for: community make me an offer!
Drop me a note to ronin42 at yahoo dot com
As measured
173
Tip 23.7
Waist 18.5
Tail 23.1
courtesy of "The Carver's Almanac (http://www.alpinecarving.com/index.html)"
Liberation Sports (http://www.liberationsports.com/), previously BS RaceBoards. Designed by BJ Slater, who formerly designed boards at NeverSummer. They make race boards and freecarve boards.
19578
19579
Dear BOL folk. I have noticed that some of the postings for sale are hard to respond to, so to make it easier I will leave my email at the bottom plus I believe my PM works.
OK here is the deal. I have a 173 BJ Slater /BS race boards/ Liberation Sports that is just too stiff for me.
The Good news: This board appears to never have been ridden there are no binding marks and the Camber is 11 mm+ on the floor and a whopping 32mm+ if against a wall. The edges are perfect, the deck is perfect using Rays way I checked the flatness of the base not concave not convex. and put a wax on it so it is ready to go.
The less then Great News: I would call this unused as opposed to new. It looks like there are a few factory blemishes.
#1 The Top sheet has what I will call a wrinkly in the red circle around the L about 1 inch long.
#2 The base right at the very back near the tail has three concave recesses where the base was pulled up into the board as it cooled. see their photo but I know it is almost impossible to see. So I don't recommend this board to anyone earning a living by going fast. for the rest of us we will never notice it.
#3 in the base I flat about a small (quarter sized bump) that was in the red circle around the L in the nose, again one can see where it was in person but not in these photos.
#4 the sidewall on the left side looks like it did not come out of the mold cleanly no core showing but not new either.
So there it is a way fast very stiff 173 GS board that has never been ridden and is completely ready to be pushed hard.
Something is worth what you can sell it for: community make me an offer!
Drop me a note to ronin42 at yahoo dot com
As measured
173
Tip 23.7
Waist 18.5
Tail 23.1
courtesy of "The Carver's Almanac (http://www.alpinecarving.com/index.html)"
Liberation Sports (http://www.liberationsports.com/), previously BS RaceBoards. Designed by BJ Slater, who formerly designed boards at NeverSummer. They make race boards and freecarve boards.
19578
19579