PDA

View Full Version : FS: Burton 7° Lift/Cant Plate


r_starr
November 19th, 2007, 03:26 PM
Burton 7° Lift/Cant Plate, with 3 and 4 hole inserts, 4 mounting screws, and Burton adapter disk.

I have 2 sets of these.

$30 each set includes shipping and delivery confirmation to continental U.S.

Thanks, Rob
Thor VonRippington
November 19th, 2007, 03:41 PM
I'll take them both!
DiveBomber
November 19th, 2007, 04:12 PM
will that work with soft boot bindings?
pebu
November 19th, 2007, 05:04 PM
Dang you TVR.
www.oldsnowboards.com
November 19th, 2007, 10:52 PM
Score Thor!! :biggthump

One more board set up!!
Thor VonRippington
November 20th, 2007, 12:10 AM
Score Thor!! :biggthump

One more board set up!!

Indeed! The whole quiver will now have identical setups... for the moment.
BadBrad
November 20th, 2007, 06:53 AM
Thor, I'm assuming that you are using these on the rear bindings only, correct? Can you give some more details on your size/weight, stance width, and angles?

I'm just curious because I used to use a cant/lift plate like this on the rear binding, then later went to running the bindings flat with some rear heel lift and just a bit of front toe lift, but this was with a narrow stance (16-17"). I recently got a new, longer board, and I am widening my stance up to around 19-20" and I'm wondering if I want to go back to a rear cant/lift plate. (I already have one like the one you're selling.)
carvedog
November 20th, 2007, 09:32 AM
Pebu
pretty sure I have one I havn't used in a while. I would do the same deal if you're interested. Need to find it first, but I think I have a clue (not) on where it is.
Thor VonRippington
November 20th, 2007, 09:39 AM
Thor, I'm assuming that you are using these on the rear bindings only, correct? Can you give some more details on your size/weight, stance width, and angles?

Not sure how phat I am has anything to do with my setup... but I'm about 6' 210lbs (I started using this setup long before I reached 210). I ride a 20 1/4" stance width and 63/60 for binding angles (my powder deck has slightly more relaxed angles). I use the cant on both front and back binding which at those angles is mostly toe lift in the front and heel lift in the back.

BTW... If anyone ever wonders what the cant angle of the Burton cant plate is in relation to a Bomber cant plate angle, it's 70 degrees (90 degrees being pure cant straight down the apex of the board).
r_starr
November 20th, 2007, 10:32 AM
Sold to Thor, thanks! DiveBomber, my guess is that they would work with soft boots but don't know for sure. Rob
www.oldsnowboards.com
November 20th, 2007, 12:42 PM
will that work with soft boot bindings?

Burton built a 3 degree "Min" cant and a 7 degree "Max" cant that are round and designed to work with soft bindings and the wider freestyle boards. The 3 holes are around, four holes were made for a much shorter period of time and therefore less common. They do add weight, however they are also pretty burly in design. FYI
BadBrad
November 20th, 2007, 02:24 PM
I do have the 3 degree Burton cants as well, but they are the 3-hole version. The 7-degree cants I have can be switched between 3 or 4-hole with different center inserts, but the the 3-degree cants don't appear to be convertible. I wish I had the 3-degree cants in a 4-hole configuration. I'd like to just a little bit of canting on the rear binding on my Prior 4WD with Burton Race Plates.
dhrracer
November 20th, 2007, 08:14 PM
I have an assortment of Burton cants and parts I will try and get pics up in the next few days.What I did when I wanted a 3deg in a four hole pattern was to get TD 1 second board kit then with a 3/8"thick T1 aluminum plate adapted Burton Race Plate toe and heal pods the Bomber cants.I'll post pics of these too.
Thor VonRippington
November 20th, 2007, 08:17 PM
I have an assortment of Burton cants and parts I will try and get pics up in the next few days.What I did when I wanted a 3deg in a four hole pattern was to get TD 1 second board kit then with a 3/8"thick T1 aluminum plate adapted Burton Race Plate toe and heal pods the Bomber cants.I'll post pics of these too.

dhrracer - please contact me here ssegress@earthlink.net
I would like to know what you have for parts...will likely buy whatever you have so you don't have to bother with a post. Thanks!
Thor VonRippington
November 20th, 2007, 09:00 PM
Thanks for the mail dh... give me a call or hit me tomorrow!
pebu
November 20th, 2007, 09:01 PM
http://www.azponds.com/Matala_Pond_Vacuum_ll.jpg


:)

I'm just kiddin around. Thor actually sold me some bindings. He's not a black hole of gear.
Thor VonRippington
November 20th, 2007, 09:03 PM
Just certain gear! :ices_ange
pebu
November 20th, 2007, 09:21 PM
It's ok, I feel the urge myself as well. I never would have said about myself that I have self control... I guess thats what happens when you really want to buy yourself some land.
dhrracer
November 21st, 2007, 03:03 PM
It's ok, I feel the urge myself as well. I never would have said about myself that I have self control... I guess thats what happens when you really want to buy yourself some land.Once again Thor scores,I am going to be sending him whay I dont need and then whoever needs something Thor can be the source!